Friday 6 May 2016

Pass4sure Cisco 300-115 Practice Test

Cisco
Exam 300-115
Implementing Cisco IP Switched Networks
Version: Demo
https://www.pass4sures.com/300-115.html

[ Total Questions: 10 ]
Question No : 1
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.





Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. Which of the following configuration steps will allow creating private VLANs?

A. Disable VTP pruning on SW1 only
B. Disable VTP pruning on SW2 only
C. Disable VTP pruning on SW4 only
D. Disable VTP pruning on SW2, SW4 and New_Switch
E. Disable VTP pruning on New_Switch and SW4 only.

Answer: C

Question No : 2
What is the function of NSF?

A. forward traffic simultaneously using both supervisors
B. forward traffic based on Cisco Express Forwarding
C. provide automatic failover to back up supervisor in VSS mode
D. provide nonstop forwarding in the event of failure of one of the member supervisors

Answer: D

Question No : 3
On which interface can port security be configured?

A. static trunk ports
B. destination port for SPAN
C. EtherChannel port group
D. dynamic access point

Answer: A

Question No : 4
Which SDM template disables routing and supports the maximum number of unicast MAC addresses?

A. VLAN
B. access
C. default
D. routing

Answer: A

Question No : 5
The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?

A. The command effectively removed all other working VLANs and replaced them with the new VLANs.
B. VTP pruning removed all unused VLANs.
C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.
D. Allowing additional VLANs across the trunk introduced a loop in the network.

Answer: A

Question No : 6
A network engineer is extending a LAN segment between two geographically separated data centers. Which enhancement to a spanning-tree design prevents unnecessary traffic from crossing the extended LAN segment?

A. Modify the spanning-tree priorities to dictate the traffic flow.
B. Create a Layer 3 transit VLAN to segment the traffic between the sites.
C. Use VTP pruning on the trunk interfaces.
D. Configure manual trunk pruning between the two locations.

Answer: C

Question No : 7
After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?

A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.

Answer: B

Question No : 8
Refer to the exhibit.

What is the result of the SPAN configuration on a Cisco switch?
A. Configure a SPAN session to monitor the received traffic on interface g0/4 only for VLAN 3.
B. Configure a SPAN session to monitor the received traffic on interface g0/4 for all VLANs except VLAN 3.
C. Configure a SPAN session to monitor the received traffic on interface g0/5 only for VLAN 3.
D. Configure a SPAN session to monitor the received traffic on interface g0/5 for all VLANs except VLAN 3.

Answer: A

Question No : 9
Which configuration command ties the router hot standby priority to the availability of its interfaces?

A. standby group
B. standby priority
C. backup interface
D. standby track

Answer: D

Question No : 10
Refer to the exhibit.

Which configuration ensures that the Cisco Discovery Protocol packet update frequency sent from DSW1 to ALS1 is half of the default value?

A. DSW1(config)#cdp timer 90
B. DSW1(config-if)#cdp holdtime 60
C. DSW1(config)#cdp timer 30
D. DSW1(config)#cdp holdtime 90
E. DSW1(config-if)#cdp holdtime 30
F. DSW1(config-if)#cdp timer 60

Answer: C